Water Filter Instructions
Katadyn Guide Filter

Compliments of
Black Mountain Stores, Inc.

1. Connect Hoses
   Remove the plastic caps from the input and output barbs on the pump base; retain for storage. Connect large diameter input hose to large diameter input barb on the pump base. Connect the small diameter output hose to small diameter output barb on the pump base. Connect the EasyFill Bottle Adaptor to the end of the output hose.
2. Flush System
   Important: Before first use, flush system by pumping approximately 1 liter of water through the unit to remove harmless carbon dust. Slightly discolored water is normal when flushing.

1. Place input hose in untreated water source. Adjust the float to keep prefilter off the bottom and away from sediment.
2. Insert the EasyFill Bottle Adaptor into a clean water container.
3. Make sure the hoses are not kinked. Begin pumping the handle in a slow, steady manner. Approximately 36 strokes per minute equals one liter of water.
4. After filling water container with filtered water, remove bottle adaptor from container and prefilter from water source. Continue pumping to remove remaining water from pump body.
5. Store unit in the carry bag. To prevent the possibility of cross-contamination, remove the output hose and EasyFill Bottle Adaptor and store separately in the resealable bag inside the carry bag.

1. Fill a liter container with tap water and add 2 tablets of Micropur Purification. If not available use 2 tablespoons of ordinary household bleach.
2. Place prefilter into solution.
3. Pump entire amount of solution through unit (into sink or container).
4. Remove prefilter from the solution and continue pumping another 5 to 10 strokes to remove remaining water from the pump body and hoses.
5. Remove cartridge and allow to dry.
6. Wrap hoses around body and store in carry bag.

1. Remove input and output hose from base. Unscrew the base.
2. Grasp housing and firmly push on top of handle to remove the cartridge from the housing.
3. Grasp cartridge and remove from handle shaft. If on trail, pack out used cartridge and discard in trash receptacle.
4. Rinse inside of Guide housing with clear water (non-filtered water is OK). Wipe inside of housing and housing threads with soft cloth to remove sediment.
5. Remove new cartridge from packaging.
6. Insert new cartridge onto handle shaft and into housing. Important: Make sure that o-ring seal on the bottom of the cartridge is evenly seated around the housing.
7. Reassemble base and hoses.
8. Flush cartridge by pumping and discarding the first liter.

1. If handle is hard to push:
   Lubricate pump handle o-ring. Silicone lubricant is provided with your new unit. Unscrew the pump base and remove filter cartridge, clean excess build-up from black rubber o-ring on bottom of handle. Place a small amount of silicone lubricant all the way around the o-ring. Re-assemble.
   
   Clogged cartridge:
   A clogged cartridge requires replacement. As a temporary solution in the field, remove the cartridge and swish it around in water. Take care that untreated water does not enter the bottom end of the cartridge. If flow is not restored, replace the cartridge.
2. If unit pumps easily, but no water flow:
   Make sure prefilter is submerged.
   Make sure that hoses are not blocked or pinched.
   Clean check valve. Occasionally, sediment may enter pump body and prevent check valve from operating properly. This may cause lack of water fraw. The check valve can easily be cleaned to restore maximum water output. Unscrew the pump base. Grasp housing and firmly push on top of handle to remove the cartridge from housing. Grasp bottom of cartridge and remove from handle shaft. Use a flat device to remove check valve band. The check valve band is the 1/4" rubber band seal on bottom end of the cartridge. Rinse check valve band. Wipe sediment from the four small holes underneath the check valve band. Reinstall check valve band. Reassemble.
3. Prefilter:
   Rinse the prefilter in water to remove any particles that may be caught in the strainer. For a more thorough cleaning, remove the prefilter from the input hose and clean with water and a soft brush. Re-assemble. Apply a small amount of silicone lubricant in the strainer barb for easy assembly.
4. For use without the weight:
   The prefilter is functional with or without the weight (we recommend using with the weight). To use without the weight, remove the strainer barb from the input hose. Re-assemble without the weight.
5. Storage:
   Your Katadyn water system comes with a carry bag for storage. To prevent the possibility of cross contamination, remove the output hose and EasyFill Bottle Adaptor and store separately in a resealable bag inside the carry bag.

• Make sure that prepared food is thoroughly cooked.
• Select non-cooked foods (fruit, nuts, etc.) that have intact shells or skins, and clean your hands before peeling the food.
• Wash your hands with soap and water thoroughly and often, especially before you eat. Filter all drinking water with your Katadyn Guide Water Filter.
Caution: If there is any risk of small bacteria or viruses in the water, use an EPA registered disinfectant such as Micropur, or boil your water.

The Katadyn Guide Filter is an essential piece of outdoor equipment. We hope it makes your outdoor experience more enjoyable. For questions or suggestions, please contact Katadyn Consumer Relations at 1-800-755-6701.

Limited Warranty
Your Katadyn Guide Microfilter is warranted for one (1) year from the date of purchase against defects in materials and workmanship. Should your Katadyn Guide prove defective within one year from the date of purchase, return it to the Katadyn retailer from whom it was purchased. If you do not receive a satisfactory solution, contact Katadyn Consumer Relations at 1-800-755-6701 for service assistance. Katadyn, at its discretion, will replace or repair the damaged item. Please retain your purchase receipt as proof of date purchased. This warranty gives you specific legal rights and you may have other legal rights which vary from state to state.